Page Comparison

Copy your data to the Outer limit folder

1. In the folder 1. Martime lines / 200M lines right click Baseline_Atlantis + 200M and click Copy.
2. In the folder 4. Outer limit right click the folder Formulae and click Paste.
3. In the folder 1. Martime lines / 60M lines select all the lines, right click, and click Copy.
4. In the folder 4. Outer limit right click the folder Formulae and click Paste.
5. In the folder 3. Sediment Data / Sediment Thickness Points select all the lines, right click, and click Copy.
6. In the folder 4. Outer limit right click the folder Formulae and click Paste.
7. In the folder 1. Martime lines / 100M lines right click atlantis's 2500 meter isobath + 100M and click Copy.
8. In the folder 4. Outer limit right click the folder Constraints and click Paste.
9. In the folder 1. Martime lines / 350M lines right click Baseline_Atlantis + 350M and click Copy.
10. In the folder 4. Outer limit right click the folder Constraints and click Paste.

All necessary data should now be in one of the folders in the Outer limit folder.

Getting familiar with the Outer Limit Menu

1. Right click the folder 4. Outer limit and click Generate Outer Limit
2. Observe the different datasets and folders in the menu.
3. Check the box next to the Formulae folder.
4. Click the icon at the top of the menu to display all the activated datasets.

Digitize the outer edge

1. Click the Start Digitize button.
2. Snap to a point on the 200M line by placing your mouse cursor over the line in the East Sea area and clicking the left mouse button.
3. We are now going to follow this line north until we meet the crossing 60M line. Place your cursor close to the crossing between the 200M line and the 60M line and press s on the keyboard.
4. We now want to follow this 60M line until me meet the next crossing 60M line. Place your cursor close to the crossing between the 60M line we are at and the next 60M line and press s
5. Again we want to follow this 60M line until me meet the next crossing 60M line, but we want to make sure it follows the outer part of the 60M line. Place your cursor somewhere on the outer part of the 60M line and press m.
6. Follow the line to the next 60M crossing line by placing your cursor close to the crossing between the 60M line we are at and the next 60M line and press s.
7. We now want to follow this 60M line until me meet the crossing 200M line. Place your cursor close to the crossing between the 60M line we are at and the 200M line and press s
8. We now want to follow the 200M line until me meet the crossing 60M line again. Place your cursor close to the crossing between the 200M line and the crossing 60M line and press s
9. We now want to follow this 60M line until we can reach the sediment thickness points. Place your cursor further up on the 60M line and press m
10. When you can see the sediment thickness points inside the white circle you can connect to them by clicking the left mouse button. Tip: place the cursor outside the point furthest out to snap to the "maximum" point.
11. Continue to click the left mouse button until you are passed the sediment thickness area.
12. We now want to connect to the 60M line in the north. Place your cursor close to the crossing between the 60M line and the white 60M circle and press c.
13. We now want to follow this 60M line until me meet the crossing 200M line, but we want to make sure it follows the outer part of the 60M line. Place your cursor somewhere on the outer part of the 60M line and press m.
14. Follow the line to the 200M crossing line by placing your cursor close to the crossing between the 60M line and the 200M line and press s.
15. We now want to follow this 200M line a little bit further to the west. Place your cursor somewhere to the west on the 200M line and press m.
16. Stop digitizing by clicking End Digitize
17. You will be asked to specify a name. Type in Outer Edge Limit and click OK
18. The dataset is stored in 4. Outer limit / Outer Limit click OK
19. Click Close to close the Outer Limit Menu

Investigate the Outer Edge Limit line metadata

1. In the folder 4. Outer limit / Outer limit right click Outer Edge Limit and click Table View.
2. Look at the information in the different columns and scroll down the list of points.
3. Click Close when you are done.

Optimize the Outer Edge Limit

1. In the folder 4. Outer limit / Outer limit right click Outer Edge Limit and click Optimize outer limit
2. Keep the default settings and click Execute. The result will be stored in the same folder
3. Click OK to close the menu
4. In the folder 4. Outer limit / Outer limit right click Outer Edge Limit Optimized and click Display
5. Investigate the areas that have been bridged.

Digitize the constraint line

1. Make sure the graphics window has been cleared by clicking
2. Right click the folder 4. Outer limit and click Generate Outer Limit
3. Check the box next to the Constraints folder.
4. Click the icon at the top of the menu to display all the activated datasets.
5. Click the Start Digitize button.
6. Digitze the constraint line using a combination of your mouse and keyboard short cuts.
7. Click End Digitze
8. You will be asked to specify a name. Type in Constraint Line and click OK
9. The dataset is stored in 4. Outer limit / Outer Limit click OK
10. Click Close to close the Outer Limit Menu
    

1. Make sure the graphics window has been cleared by clicking
2. Right click the folder 4. Outer limit and click Generate Outer Limit
3. Check the box next to the two datasets Outer Edge Limit Optimized and Constraint Line
4. Click the icon at the top of the menu to display all the activated datasets.
5. Click the Start Digitize button.
6. Digitze the final outer limit line using a combination of your mouse and keyboard short cuts.
7. Click End Digitze
8. Keep the default nameand click OK
9. The dataset is stored in 4. Outer limit / Outer Limit click OK
10. Click Close to close the Outer Limit Menu