Page Comparison

{section}
{column:width=70%}

h2. Introduction

!att:_img_gen^axes_annotation_scalebar.png|border=1,width=800!
_Example of a scene with axes, annotation and scalebar_

Geographical grids, axes annotation, scalebars and text are natural display features when working out displays and presentation graphics. This chapter gives a brief documentation of the standard menus for text and annotation graphics in the system.
{column}
{column:width=30%}
\\
\\
*On this page:*
{toc:maxLevel=3}
{column}
{section}

h2. Geographical coordinates with axes

Use the command *Geographical coordinates* to display axes and coordinate annotation on a dataset.

!att:_img_gen^axes_annotation.png|width=900!

Geographical coordinates can be accessed as a command (found in *Shared Commands > Visualization*) or as a stand alone menu from *Tools > Geographical Management*. In either case the rules for a correct display is the same.

* Push *Default display* (older version only *Display*) under *Default display* to see the default values.
* Type in *Longitude/Latitude start*, *Long/Lat increment* and *Longitude/Latitude stop* values to set a custom geographical grid.
* Push *Display* or *Execute* to display geographical coordinates using the Lat / Lon values.
* To get a nice placement of the annotation numbers use the tuning in *Adjust annotation numbers*.

{tip}
Sometimes it may be useful to create an item command that will save your settings for a specific dataset. This will save you time next time you want to display axes over the same area. Read more about [creating item commands|Customizing the Interface#Creating item commands].
{tip}

h4. A simple guide on how to achieve a good display
The geographical axes display will be within the graphical window. To see the graphical window push the *Draw Frame* icon !att:_img_icon^draw_frame.png! on the toolbar.

# Make sure you have scaled to the dataset you want to display together with the axes.
# Check that the correct *coordinate system* is set under the *Coordinates* page.
# Go to get a *Default display*  section and click *Display*.
	
Sometimes the algorithm get a good display, but normally the user must edit the settings in the *Detailed display* section.
	
# Push *Update detailed* to get the Lat / Lon values into the number fields.
# Adjust them and click *Display* to see the changes.

Continue this process until you have achieved a satisfactory result.

h4. An illustrated guide
A part of the *Atlantis* project is used to display a map and geographical coordinates. The assumed projection is *Mercator*, but we will also study the display when assuming other projections.

{section}
{column:width=50%}
!att:_img_gen^gc_defdis.png!
The default display for *Mercator* appears OK, but can be improved. Push *Update detailed* to transfer default values over to the Lat / Lon fields.
{column}
{column:width=50%}
!att:_img_gen^gc_adjust1.png!
Use *Adjust annotation numbers* to get a better positions of the coordinate numbers. Here the _right_ number was adjusted to -25 and _Up_ to 5. The *Longitude start, increment, stop* is *-14  2  0*. The *Latitude start, increment, stop* is *-34  2  24*. 
{column}
{section}

{section}
{column:width=50%}
!att:_img_gen^gc_adjust2.png!
To display annotation numbers for every line change the number next to *Auto annotation* with the tooltip *Frequence of annotation number* to 1.
We see that the minutes are zero and change *Annotation format* to *DD* (Only degrees). At the same we check in for *E/W/N/S*. 
{column}
{column:width=50%}
!att:_img_gen^gc_adjust3.png!
If the coordinate system was *UTM zone 32 Northen Hemisphere* the display lines are slanted and shows different numbers. This shows that correct coordinate setting is essential for getting a correct display.

The geographical lines was displayed using *Default display*, but kept the same *adjustments of annotation numbers* as before.
{column}
{section}


{section}
{column:width=50%}
!att:_img_gen^gc_adjust4.png!
To get annotation display along all side change default *NE* to *all*. For a little display like this it is necessay to adjust all numbers. This particular setting was *-25 50 5 -20* for *Right Left Up Down*.
{column}
{column:width=50%}
!att:_img_gen^gc_persp.png!
To get the coordinate lines displayed on the surface one has to check in the *Sticky* checkbox and also apply *Set as sticky surface* on the surface grid. 
{column}
{section}


h2. Scale bar

To display a scale bar open *Tools > Scalebar display*

!att:_img_gen^scalebar.png|width=700!


* Push *Draw Scalebar* to display the scalebar in default position and appearance.
* To place the scalebar at specific position:
{indent}
# Set the screen in 2D mode.
# Tick the box *Use XYZ coordinates*
# Click in the graphic window where you want to place the scalebar.
# Click *Update cursor to world coordinates* to get the cursor coordinates.
# Redisplay scalebar by pushing *Draw Scalebar*
{indent}

The default scalebar display will be within the graphical window and the drawing size is related to that window. To see the graphical window push the *Draw Frame* icon !att:_img_icon^draw_frame.png! on the toolbar.

h2. Text annotation

The *Three dimensional text* command lets you create text annotation anywhere in the graphical window. You can create 2D or 3D text, display the text in any angle or stick the text to a surface. All these things can be found out whith a little test and trying. When everything is fine save the command object. Optionally save it as an *Item command* or copy a present CO so you work with and save a copy of the command object.

!att:_img_gen^annotation.png|width=900!

{section}
{column:width=60%}

As an example here are the guide lines forh4. A guide on drawing a text at an angle along a line.

{note:title=Guide lines for text annotation at an angle}
* # Write in the desired text in the *text field*.
*# Set the screen in 2D mode and makecreate two cursor positions:
{indent}
# First cursor position: *at end of text*
# Second cursor position: *at start of text*
{indent}
*# If the screen is in 3D mode use *y* to attach the cursor point to a surface.
*# Push *Update cursor to coordinates*.
*# Push *Update dip and azimuth*. *Azimuth* is for rotation around z axes. *Dip* is for 3D mode.
*# Check in the *Dip* and *Azimuth* boxes.
*# Select text attributes.
*# Push *Execute* to display the text.
{note}

With a little training one can place text at any angle and position.
{column}
{column:width=40%}
!att:_img_gen^geocoord2.png|width=400!
_Example map with geo grid, scale bar end 3D text_
{column}
{section}