Page Comparison

Introduction

Geocap distinguishes between SEG-Y 2D and SEG-Y 3D files, although they are basically the same:

Left: SEG-Y 2D import, Right: SEG-Y 3D import

The main difference is that you will have to set the shot point byte position for both inline and crossline in the 3D import, while in the 2D there is of course only one shot point column. The 2D import also has a Analysis panel that lets you fix anomalies in the SEG-Y file.

For more information about the SEG-Y format, see the SEG page SEG-Y standard: http://www.seg.org/resources/publications/misc/technical-standards

The import menu

Below you will find a short explanation of the different elements in the SEG-Y import menu:

IBM float
The SEG-Y standard revision 1 defines SEG-Y files stored with IBM floating-points to have the data sample format code in the binary file header set to 1. Since many SEG-Y files have this as 1 regardless of floating-point format, check the IBM float checkbox to specify IBM floating-point.

Little-endian
Most modern computer architectures use big-endian byte order. You may come across SEG-Y files, especially older ones, that have been stored with little-endian byte order. When that happens, the information under tabs Reel header and Trace header looks garbled. Check the Little-endian checkbox to fix this problem.

EBCDIC Header
The SEG-Y EBCDIC header (textual file header) contains 3200 bytes of readable characters. SEG-Y revision 1 allows the header to be encoded in ASCII. Use the encoding combobox to switch between EBCDIC and ASCII encoding. Study the text in the EBCDIC header tab; it may give you useful information about byte positions, etc.

Reel header
The SEG-Y reel header (binary file header) contains 400 bytes of binary values that affect the whole SEG-Y file. The information in the Reel header tab includes sampling interval, number of samples per trace, data sample format code, etc.

Trace header
The SEG-Y trace header contains 240 bytes of binary trace attributes. The Trace header tab allows you to browse through all trace headers in the file. The four 'player' buttons takes you to the first-, previous-, next-, and last trace. You may also enter the trace number directly in the trace number line edit. If you change a setting (e.g. Type) that affects the information in the Trace header tab, you need to enforce an update - click button for next trace, for example - for the information to change.

Scan results
After performing a Scan the results are displayed under this tab. If more than one file is selected, the scan results are updated continuously as the different files are scanned.

Settings table
The settings table contains widgets for setting relevant trace attributes to accommodate all the different flavours of the SEG-Y standard:

• Shot point or Inline, Crossline: Type, Byte pos., Min, Max, and Step can be adjusted
• Scaler (X,Y): Value can be adjusted; Type is fixed to Integer16 and Byte pos. is fixed to the two bytes immediately preceding X
• X: Type and Byte pos. can be adjusted
• Y: Type is fixed to the same as X and Byte pos. is fixed to the corresponding bytes immediately succeeding X
• Z: Type, Byte pos., Min, Max, and Interval can be adjusted

Import 2D seismic

Analyze file

The analyze process scans the SEG-Y file looking for anomalies:

• Unassigned shot points (Taper)
• Unassigned navigation (Taper)
• Missing traces

The Analyze dialog always report the first and last trace. If only two lines appear in the dialog with nothing reported in the Anomaly column, the analysis is done.

SEG-Y analysis panel

A common anomaly found by the analyze process is taper. The phrase Taper On denotes traces in the SEG-Y file that occur before full fold is obtained. If the phrase Taper Off is reported it means that taper occurs at the end of the file. Taper are usually handled by assigning shot points to the corresponding traces. The assigning algorithm suggests a shot point for the taper trace next to the normal trace. Go with this suggestion unless you have special considerations. Shot points are then assigned to the taper traces in an orderly fashion. You may also assign navigation to the taper traces; inspect the X- and Y columns to see whether they already have navigation, and if it is correct. Navigation is assigned by way of extrapolation.

The analysis may find missing traces. Those are traces that normally should have been in the file but have been omitted for some reason. The Insert button will insert dummies for these missing traces.

Scan file

It is always recommended to scan the SEG-Y file before import, to make sure the settings for each trace attribute are correct. Click the Scan button and observed the results in the Scan Results tab.

Example of scan results

Shot point byte position

If the Min and Max values for Shot point looks odd, the byte position could be wrong. The default shot point byte position in the SEG-Y 2D import is 17-20 in the trace header, but in some cases this is not always correct. If the byte position is wrong try the following:

• Look for information about the shot point byte position in the EBCIDIC header.
• Select the Trace header tab to view the SEG-Y file's headers trace by trace. The byte positions' values are continuously reported as you move through the file. By closely observing how the values change you should be able to determine the correct byte position.

  Note
  Shot points often appear in pairs, i.e. they change every other trace.

Use the Shot point, Byte pos. spinbox to set the appropriate byte position.

Coordinates and scaler

Make sure the X coordinate has 6 digits and that the Y coordinate has 7 digits. In some cases the scaler may be wrong, causing the X and Y values to have to few or to many digits. This can be adjusted by changing the scaler multiplication factor.

Z(twt)-range and sample interval

The Z values are usually correct but you can have a look in the EBCIDIC header to see if there is any information about the sample interval or Z-range.

Import multiple files

Geocap lets you import multiple SEG-Y files in one go. Since Analyze and Scan makes no sense for multiple files, they are disabled. A combobox with analysis options is enabled instead. The entries are:

• Normal (files read as is)
• Full auto - Equivalent to both Auto assign shot point and Auto assign navigation.
• Auto assign shot point - Equivalent to pushing assign shot point button in Analyze dialog for all files.
• Auto assign navigation -Equivalent to pushing assign navigation button in Analyze dialog for all files.
• Auto omit taper on/off - Equivalent to manually omitting taper traces by setting Shot point Min all files.

Import 3D seismic

The resulting data set's name in the project is either based on the file name or byte positions in the EBCDIC header. To set EBCDIC header byte positions simply highlight the section you want as data set name. The label between the comboboxes always shows current name.