Introduction
In order to calculate HCPV (i.e. hydrocarbon pore volume) for the reservoir there has to be a reservoir model. This is a folder with reservoir horizons in a layer model and folders with petrophysical parameter grids.
The parameter grids are connected to the zone between two horizons and the zones in the layer model start with the first horizon. There are seven horizons and six zones; therefore the last horizon will have no petrophysical parameter grids associated. The parameter grids can be found in the folder 09_Petrophysical parameters.
The petrophysical parameter grids in the volumetric model are random generated between 0.1 and 0.6 approximately. That corresponds to realistic value domains. In real cases the petrophysical parameter grids are gridded from well data, f.inst. using the gridding panel Simple points and lines gridding
Exercises
Layer model and cross sections illustrating a zone
Calculate Volume
Calculate hydrocarbon pore volume within a license.
- Right click on Depth data > Grids interpretation and select Utilities > Volume layer model calculation.
- Set Type of volume to be calculated to Between plane1 and plane2.
- Check in 1: contact and write in the level value 2700 (suitable for this project). Also called top contact
- Check in 2: contact and write in the level value 3800 (suitable for this project). Also called bottom contact
- Check in Apply folder or single area grid or outline for licenses or sub areas.
- Browse in 01_Cultural Licenses > License 07-18.
- Go to page Parameters
- Check in boxes for petrophysical parameters and browse in the corresponding folders.
- Check in Expansion oil and set the value to 1.2.
- Check in Recovery factor oil and set the value to 0.4.
- Click Execute to start calculation.
- Go to Result page and take a look at the table view
- Click on Volume report to disk
The volume report is saved to your home area on disk by default and is placed in a folder. The names are made of parameters set and a time stamp i.e.:
- Folder: Volumetric reports_Grids Interpretation_Sun Sep 22 2013.
- Report: VR_Grids Interpretation_2700_3800_Licens 07-18_b_p_n_w_Sun Sep 22 21_11_08 2013.
If there is only one contact plane you just check in 1: contact.
There are two types of calculation:
- From top reservoir to Top contact.
- Between Top contact and Bottom contact.
Project: Course B1 Volumetric report for horizons in folder: Grids Interpretation. Calculated and saved at: Wed Nov 16 08_55_46 2011 Parameters present and used: Type of volume to be calculated: Between plane1 and plane2 First horizon used: 02BasePliocene Last horizon used: 07Silurian Contact plane 1: 2700 Contact plane 2: 3800 License or sub area: License 07-18 Porosity folder: Porosity Net to Gross folder: Net to Gross Water saturation folder: Water Saturation Expansion value oil: 1.2 Recovery factor oil: 0.4 Units used in report table: Cubic km (10^9) Zone Bulk Pore HCPV InPlace Recoverable 02BasePliocene 57.859400 33.751980 10.205310 12.246370 4.898550 03UpperCretaceous 446.479170 174.687160 41.260900 49.513080 19.805230 04LowerCretacUCo 794.343640 384.093490 79.636180 95.563410 38.225360 05BaseJurassic 4603.565830 1667.313830 563.336510 676.003810 270.401530 06BaseTriassic 1299.398520 542.952390 85.428700 102.514440 41.005780 Total 7201.646570 2802.798850 779.867600 935.841120 374.336450
How the Volume report looks like in an editor.
Display features
Display recoverable hydrocarbon volume within a license.
- Go to the Display tab
- Select zone 4.
- Set option to As single volume.
- Click Display volume or contact area.
- Study the display and explain the map.
Base Jurassic recoverable volume as single volume grid
Display hydrocarbon volume and cross sections.
- On the Display tab select zone 3.
- Set option to On bottom of horizon.
- Click Display volume or contact area.
- Make a cursor position by pressing y on the keyboard.
- Click Get cursor values.
- Make sure X direction is checked.
- Click Perform cross section from position values.
- Study the display and explain the map.
Base Jurassic draped on Base Triassic and cross sections
Display hydrocarbon volume and fence diagram.
On the Display tab select zone 4.
- Set option to On top of horizon.
- Click Display volume or contact area.
- Click Fence diagram cross sections.
- Study the display to and explain the map.
Volume draped on Base Jurassic and fence diagram
Display recoverable hydrocarbon volume within a license.
- On the Display tab select zone 4.
- Set option to On top of horizon.
- Check in Display contact area (on zone top only).
- Click Display volume or contact area.
- Check off Erase screen.
- Select zone 5.
- Click Display volume or contact area.
- Go to the Volume page and display the contact planes.
- Study the display to and explain the map.
Base Triassic and Silurian and contact planes
Advanced display of volumetric results
Viewports are a good way to present the results.
Display the volume grids for all zones in the layer model.
- Click on the
icon on the toolbar to open the viewport menu. - Check in Connect all viewports and Draw viewport frame.
- Create 2 x 3 viewports. You now have 6 connected viewports.
- Click on viewport at upper left to get that viewport frame in red.
- Go to the Display page on the volume calculation menu
- Select zone 1. Select On top of horizon. (All selections will do, and one must be consequent).
- Click Display volume or contact area.
- Go to the shell and type the text: tx2 .7 lle col bla txt "Base Pliocene". (2D text at lower left; see the ref. manual).
- Click on the next viewport.
- Select zone 2 and repeat the previous steps for zone 2.
- Repeat the steps for zone 3, 4 and 5.
- Put the viewports in 2D mode to see it from above.
- To display the lower right viewport (it is number 2) in 3D mode do as follows:
- Go to the command shell and type: vie 2 con off.
- Check in Display contact area (on zone top horizon only).
- Select zone 5.
- Click Display volume or contact area.
- Make a proper size of the screen and apply generic folder >New > Screenshot to save the picture.
Volume display for all zones